Secure enquiry - no spam, no pressure. Genuine quotes only.
Need a reliable replacement engine for your Dodge Caliber?
Engine Finders specializes in Caliber engines, addressing shared World Engine, CRD diesel, and turbo
reliability issues across the entire model range.
Rebuilt to resolve oil consumption and bottom-end wear on World Engines.
Factory-spec rebuilds correcting piston ring and balance shaft failures.
Inspected engines addressing overheating, gasket failure, and compression loss.
Direct-fit Dodge Caliber replacement engines for seized or failed units.
Updated components to reduce oil burning and long-term reliability issues.
Lower-cost engines with verified mileage for short-term ownership solutions.
Engine Finders connects UK drivers with vetted specialists for reliable, reconditioned Dodge Caliber replacement engines. The Caliber range (2006–2012) spans shared World Engine petrol units (1.8, 2.0, 2.4), the Volkswagen-derived 2.0 CRD diesel, and the turbocharged 2.4 SRT4 powertrain—each used across multiple trims and years. From widespread oil consumption and timing component wear in World Engines to injector and EGR failures affecting all CRD variants, we source series-correct engines built to address the Caliber’s most common cross-range weaknesses.
All Caliber World Engines (1.8/2.0/2.4 GEMA) share piston ring design issues leading to oil burn across the entire series. Our rebuilds upgrade oil control rings (OEM 4884412AB) and revised pistons to prevent repeat failures—an approach proven across all petrol Caliber variants.
The 2.0 and 2.4 World Engines use the same timing chain and tensioner system (OEM 4884483AC) across the Caliber range. Engine Finders supplies engines rebuilt with updated tensioners and guides to eliminate the series-wide cold-start rattle and chain stretch issues.
Every Caliber 2.0 CRD uses the VW EA188 diesel architecture, sharing identical piezo injectors (OEM 03G130073T) and EGR assemblies. We match customers with engines rebuilt to address clogging and injector imbalance that affects the full diesel lineup.
The Caliber SRT4’s 2.4 turbo engine uses a common turbocharger assembly (OEM 4891765AD) across all production years. Our sourced engines feature upgraded oil feed and bearing checks to counter the series-known turbo wear and heat-soak failures.
All Caliber engines share a similar cooling layout, with thermostat housings (OEM 4892498AA) prone to cracking over time. Engine Finders prioritizes engines rebuilt with reinforced housings to prevent overheating common to the entire Caliber range.
Petrol, diesel, and SRT4 Caliber engines all rely on generation-specific ECUs sharing common connectors and immobiliser logic. We ensure correct ECU compatibility using OEM control modules (e.g., 05094948AD) to avoid non-start issues across all trims.
Whether replacing a World Engine petrol unit, CRD diesel, or SRT4 turbo motor, Caliber owners face similar dealer-level costs. Engine Finders sources series-specific engines that routinely save £1,500–£3,000 compared to main dealer replacement across the entire lineup.
Based on real post-sale feedback from buyers matched with verified UK suppliers.
Engine Finders connects UK drivers with trusted suppliers of Dodge Caliber replacement engines. Whether facing oil consumption in World Engine petrol units or EGR and injector failures across CRD diesels, we source reliable OEM-fit solutions for the full Caliber series.
The Dodge Caliber was produced on Chrysler’s PM/MK platform, sharing powertrain architecture across all trims and markets. Petrol variants used the Global Engine Alliance “World Engine” family, while diesel models relied on Volkswagen-sourced CRD units. Across the series, common replacement triggers include excessive oil consumption and balance shaft wear in 2.4L petrol engines, timing chain stretch in high-mileage World Engines, and injector, turbocharger, and EGR valve failures affecting all 2.0 CRD outputs. Chrysler technical updates focused on revised piston rings and PCV systems for petrol engines, while diesel service bulletins addressed injector sealing and EGR reliability. Because these engines were shared unchanged across the Caliber range, failures occur consistently regardless of trim or gearbox, making correct engine-family matching essential when sourcing replacements.
The Caliber range was supported by a small number of shared engine families, each used across multiple trims and years on the PM/MK platform.
Because engine mounts, ECUs, and ancillary layouts are consistent across the PM/MK platform, replacements must match engine codes precisely rather than trim names.
For the Caliber series, engine choice depends on known cross-variant weaknesses. Used engines may carry unresolved oil control or injector faults common to these families, while reconditioned and remanufactured options include updates addressing shared failure points across petrol and diesel units.
All options are selected to suit the full Caliber range rather than individual trims.
Our stock covers all major Dodge Caliber engine families used on the PM/MK platform. Reconditioned petrol engines include revised timing components, piston rings, and oil control updates, while CRD diesel units feature refurbished injectors, turbochargers, and EGR systems common across the series.
Every engine is compression-tested and bench-run to ensure series-wide OEM performance compliance.
All Dodge Caliber replacement engines supplied through Engine Finders include a standard UK warranty covering the complete PM/MK series.
Engine Finders is a comparison platform; final warranty terms are set by individual UK suppliers and may vary by engine family and mileage.
When your engine fails, Dodge Caliber engine works can restore performance at a fraction of the cost of a brand-new engine. From diagnostics to rebuild, here's how experts ensure optimal results.
1. Strip-down & Inspection: Caliber engines are fully stripped with crank, balance shafts and head removed. PM/MK-specific wear areas are measured, including oil pump clearances and cylinder ovality common on World engines used between 2006–2012.
2. Block & Crank Machining: Blocks are honed to Caliber tolerances, cranks polished or reground. Balance shaft bearings—critical on 2.0 and 2.4 petrol units—are replaced to prevent vibration issues unique to the Caliber setup.
3. Head Reconditioning: Cylinder heads receive valve guides, stem seals, and pressure testing. CRD heads get injector seat cutting, a known Caliber diesel failure due to factory sealing design.
4. Component Replacement: Pistons, rings, bearings, chains, and oil pumps are renewed. Caliber-specific updates include revised oil control rings and uprated turbo oil feeds on CRD engines to match original factory revisions.
5. Precision Reassembly: Engines are rebuilt using Caliber torque specs and sequence data. Clearances are checked against PM/MK tolerances to ensure smooth running across all Caliber variants.
6. Testing & Validation: Each rebuilt Caliber engine is hot-run or compression-tested, oil pressure verified, and leak-checked. Only units meeting Caliber performance benchmarks are approved for UK delivery.